Page 16 of 16 FirstFirst ... 6141516
Results 451 to 472 of 472

Thread: Middle-aged kit building

  1. #451
    Join Date
    Jun 2003
    Posts
    8,622
    http://www.astronautix.com/v/vonbraunlunarlander.html
    I recognised the 'table' that holds the fuel tanks etc.

  2. #452
    Join Date
    Jul 2005
    Posts
    17,868
    Quote Originally Posted by eburacum45 View Post
    http://www.astronautix.com/v/vonbraunlunarlander.html
    I recognised the 'table' that holds the fuel tanks etc.
    That's the one. This seemed like a good year to be building it.

    Grant Hutchison

  3. #453
    Join Date
    Aug 2005
    Location
    NEOTP Atlanta, GA
    Posts
    2,814
    Too bad you can’t build an “as flown” version.

  4. #454
    Join Date
    Jul 2005
    Posts
    17,868
    It's interesting that the photo in the Astronautix link shows Wernher von Braun holding a model that has the same "unrealistic" configuration as the Pegasus model I'm building. The very large, outermost spherical fuel and oxidizer tanks were intended to be used for translunar injection, and then discarded, like the S-IVB stage. During that acceleration phase, the legs were to be stowed out of the way of the rocket plumes - the outer ones folded forward, and the central one retracted. They were only to be deployed during the final powered descent to the moon, by which time the vehicle had a more stripped-down appearance. And the central leg was only the same length as the others once the vehicle had landed - it was intended as a shock-absorbing "probe", and initially extended beyond the plane defined by the footpads of the outer legs.

    I'm modifying my kit to depict the landed configuration.

    Grant Hutchison

  5. #455
    Join Date
    Jun 2003
    Posts
    8,622
    Thirty rocket motors! A crew of fifty! That's a spaceship. The mission seems to have been modelled on the Endurance or Discovery in the Antarctic.

  6. #456
    Join Date
    Jul 2005
    Posts
    17,868
    Quote Originally Posted by eburacum45 View Post
    Thirty rocket motors! A crew of fifty! That's a spaceship. The mission seems to have been modelled on the Endurance or Discovery in the Antarctic.
    Here's the engine array:
    Click image for larger version. 

Name:	engines1.jpg 
Views:	18 
Size:	1.13 MB 
ID:	24530
    The outer twelve could be vectored in triads for attitude control:
    Click image for larger version. 

Name:	engines2.jpg 
Views:	16 
Size:	1,006.9 KB 
ID:	24531

    According to the 1952 Collier's article, the expedition crew of 50 would have travelled in three ships, one of which replaced the lunar departure tanks (in the centre of the structure) with a cargo hold. Each ship could accommodate 25, so that the two with return take-off capability could get everyone off the moon.

    Grant Hutchison

  7. #457
    Join Date
    Jun 2003
    Posts
    8,622
    Three ships would require 90 rocket motors.
    The same number of rocket motors were used in three N1 launches. Not a resounding success.

  8. #458
    Join Date
    Jun 2004
    Location
    The Great NorthWet
    Posts
    14,582
    And of course, the BFR Starship/Superheavy is going the same way.
    Cum catapultae proscriptae erunt tum soli proscript catapultas habebunt.

  9. #459
    Join Date
    Feb 2005
    Posts
    11,593
    But with fins. And no worry about a hypergolic disaster.

  10. #460
    Join Date
    Jul 2005
    Posts
    17,868
    1/350-scale astronauts.
    Click image for larger version. 

Name:	Img_4930.jpg 
Views:	28 
Size:	743.7 KB 
ID:	24543
    1/350 is a common scale for ship models, and I managed to find some figures in that scale, to which I applied little bits of styrene strip for life-support packs, and a blob of glue for a bubble helmet. Bit of a challenge to paint, as you can see.

    Grant Hutchison

  11. #461
    Join Date
    Jun 2004
    Location
    The Great NorthWet
    Posts
    14,582
    Mercy, that's tiny!

    My first reaction to the photo was that your pennies are quite a lot bigger than ours. They aren't that much, just 1mm and change.
    Cum catapultae proscriptae erunt tum soli proscript catapultas habebunt.

  12. #462
    Join Date
    Jul 2005
    Posts
    17,868
    Click image for larger version. 

Name:	von braun lander 1.jpg 
Views:	21 
Size:	1.02 MB 
ID:	24557
    Click image for larger version. 

Name:	von braun lander 3.jpg 
Views:	19 
Size:	948.6 KB 
ID:	24558
    Click image for larger version. 

Name:	von braun lander 8.jpg 
Views:	15 
Size:	932.3 KB 
ID:	24559
    Click image for larger version. 

Name:	von braun lander 9.jpg 
Views:	16 
Size:	907.7 KB 
ID:	24560

    Grant Hutchison

  13. #463
    Join Date
    Jun 2004
    Location
    The Great NorthWet
    Posts
    14,582
    Quote Originally Posted by grant hutchison View Post
    Click image for larger version. 

Name:	von braun lander 1.jpg 
Views:	21 
Size:	1.02 MB 
ID:	24557
    Click image for larger version. 

Name:	von braun lander 3.jpg 
Views:	19 
Size:	948.6 KB 
ID:	24558
    Click image for larger version. 

Name:	von braun lander 8.jpg 
Views:	15 
Size:	932.3 KB 
ID:	24559
    Click image for larger version. 

Name:	von braun lander 9.jpg 
Views:	16 
Size:	907.7 KB 
ID:	24560

    Grant Hutchison
    Now weld some stainless steel around it....
    Cum catapultae proscriptae erunt tum soli proscript catapultas habebunt.

  14. #464
    Join Date
    Jul 2005
    Posts
    17,868

    Kicking up some dust ...

    Click image for larger version. 

Name:	liberty lander.jpg 
Views:	18 
Size:	1.04 MB 
ID:	24561
    No, honestly. That's the size of it.

    Grant Hutchison

  15. #465
    Join Date
    Feb 2005
    Posts
    11,593
    That is what should have been the first lander. Sigh....

  16. #466
    Join Date
    Aug 2006
    Posts
    3,473

    Advice for sawing fine detail

    You guys might be just the guys to help me out with this.

    I'm planning to make a landscape relief map out of foam core layers (1/4" or 1/8"). It's mountainous territory, so the cutting will be very intricate - and a lot of it. I'll print out the landscape, paste it on, then cut along the contour lines. (The printed landscape will be the final surface.)

    I tried using an X-acto knife already. It was not up to the job. Even a #11 blade, that's only a mm or two thick, does not allow me to cut the curves I want. Worse, it doesn't cut cleanly through the paper and foam core, so the contour frays or falls apart.

    I'm looking for a better - and ideally faster - way to cut.

    I have a coping saw but a flat blade will still be problematic. Ideally, I can get a blade with a circular cross-section, so I can cut in any direction. Still, using a coping saw for hours on-end will probably rattle my teeth.

    I wonder if there are hand saws for this kind of work? I'm thinking like a micro-screwdriver, but instead of a bit, it has a blade with a circular cross-section. Then it would essentially be a human-powered coping saw.

    I also thought of a hot wire but, while it might go through the foam core fine, it likely won't handle the paper very well.

    Thoughts?

  17. #467
    Join Date
    Sep 2003
    Location
    The beautiful north coast (Ohio)
    Posts
    49,158
    I don't have a good suggestion. I've used and cut foam core, but only as single layers, and an X-acto works fine.
    At night the stars put on a show for free (Carole King)

    All moderation in purple - The rules

  18. #468
    Join Date
    Sep 2004
    Posts
    15,531
    Cut out the paper separately first (any way you see fit), put it on the foam, then follow the contour with the hot wire. That way the hot wire doesn't have to cut the paper. You spend extra time because you have to cut twice, but two easy cuts might be faster and more pleasant than a combined troublesome cut.
    With sufficient thrust, water towers fly just fine.

  19. #469
    Join Date
    Aug 2006
    Posts
    3,473
    Quote Originally Posted by Nicolas View Post
    Cut out the paper separately first (any way you see fit), put it on the foam, then follow the contour with the hot wire. That way the hot wire doesn't have to cut the paper. You spend extra time because you have to cut twice, but two easy cuts might be faster and more pleasant than a combined troublesome cut.
    Thanks for the idea, but I think it will be problematic. Making circa-millimetre mistakes when cutting both is not a problem for me, but when cutting the foam to match the paper, even the tiniest divergence from the cut the paper, the edge will look terrible.

    And I've got a lot of cutting to do...

    This is about 18" square and has 20 layers.

    (I'd 3D print, but I think it's way too large/expensive. )
    Attached Thumbnails Attached Thumbnails Click image for larger version. 

Name:	topo large.png 
Views:	10 
Size:	501.9 KB 
ID:	24614  
    Last edited by DaveC426913; 2019-Oct-11 at 01:43 AM.

  20. #470
    Join Date
    Jan 2005
    Location
    New Zealand
    Posts
    10,953
    Quote Originally Posted by DaveC426913 View Post
    ...
    (I'd 3D print, but I think it's way too large/expensive. )
    Rather than 3D print, I'd have thought that's more a job for an "old fashioned" CNC router table kind of thing.

    (Dunno about the detail achievable though.)
    Measure once, cut twice. Practice makes perfect.
    Why is a frog too?

  21. #471
    Join Date
    Feb 2003
    Location
    Depew, NY
    Posts
    11,823
    My Dad is still building model castles in his 70s. Here are two pictures.

    Click image for larger version. 

Name:	SK001.jpg 
Views:	10 
Size:	203.8 KB 
ID:	24623

    This is a 25mm scale shell or motte and bailey keep. It's about 3x4 feet.

    Click image for larger version. 

Name:	CC001.jpg 
Views:	9 
Size:	353.5 KB 
ID:	24624

    This is a crusader castle. It's about the same size as the other one.

    If you want to see more details, check out my blog. Here is the shell keep. And this is the castle.

    Just an FYI - there are some ads on my page. Amazon and DriveThruRPG. For whatever reason, an adblocker will stop the Amazon ads but not the DriveThruRPG stuff. Not sure how I did that. I used to have my blogs in the sig line, but there isnt' a heck of a lot of crossover between D&D themed blogs and Space and Astronomy Forums. I used to maintain a section for an ad free experience for Forum users, but I switched to a generic blogger page and accidentally killed it.

    If there is any interest in an ad free experience for Forum users, shoot me a message. I just don't link out to my blog all that often, even though I have asked for permission to do so. It really isn't a "thing", except for large pictures.
    Solfe

  22. #472
    Join Date
    Jun 2004
    Location
    The Great NorthWet
    Posts
    14,582
    Quote Originally Posted by Solfe View Post
    My Dad is still building model castles in his 70s. Here are two pictures.

    Click image for larger version. 

Name:	SK001.jpg 
Views:	10 
Size:	203.8 KB 
ID:	24623

    This is a 25mm scale shell or motte and bailey keep. It's about 3x4 feet.

    Click image for larger version. 

Name:	CC001.jpg 
Views:	9 
Size:	353.5 KB 
ID:	24624

    This is a crusader castle. It's about the same size as the other one.

    If you want to see more details, check out my blog. Here is the shell keep. And this is the castle.

    .
    I'm also in my 70's and building machines to knock them down!
    Cum catapultae proscriptae erunt tum soli proscript catapultas habebunt.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •